title: Modes in Vim
Because Vim is focused on changing existing code just as much as writing new
code, it is split into several modes that each have different purposes.
By default, Vim starts in “normal” mode.
Normal mode can be accessed from other modes by pressing
In Normal mode key presses don’t work as one would expect. That is, they don’t insert text into the document; instead,
certain key presses can:
Move the cursor
- h move one character left
- j move one row down
- k move one row up
- l move one character right
As many vim commands, row movement can be prefixed by a number to move several lines at a time:
- 4j move 4 rows down
- 6k move 6 rows up
Basic word movements:
- w move to beginning of next word
- b move to previous beginning of word
- e move to end of word
- W move to beginning of next word after a whitespace
- B move to beginning of previous word before a whitespace
- E move to end of word before a whitespace
Beginning/End of line movement:
- 0 move to the beginning of the line
- $ move to the end of the line
Enter other modes
Normal mode is where one should spend most of their time while using Vim. Remember,
this is what makes Vim different.
In normal mode, there are multiple ways to move around an open file. In addition
to using the cursor keys to move around, you can use
l (right) to move as well. This particularly helps touch typists who
don’t like leaving the home row when making changes.
You can also make changes to single characters in normal mode. For example, to
replace a single character, move your cursor over it and press
r, and then the
character you want to replace it with. Similarly, you can delete single characters
by moving your cursor over it and pressing
To perform an undo, press
u in normal mode. This undoes changes up to the last
time you were in normal mode. If you want to redo (i.e., undo your undo) press
Ctrl+r in normal mode.
This is the second most used mode, and will be the most familiar behavior
to most people. Once in insert mode, typing inserts characters just like a regular
text editor. You can enter it by using an insert command from normal mode.
Insert commands include:
ifor ‘insert’, this immediately switches vim to insert mode
afor ‘append’, this moves the cursor after the current character and enters insert mode
oinserts a new line below the current line and enters insert mode on the new line
These commands have an uppercase variety too:
Imoves the cursor to the beginning of the line and enters insert mode
Amoves the cursor to the end of the line and enters insert mode
Oinserts a new line above the current one and enters insert mode on the new line
There are so many more ways of inserting text in Vim that can’t be listed here
but these are the simplest. Also, beware of staying in insert mode for too long; Vim is
not designed to be used in insert mode all the time.
To leave insert mode and return to normal mode, press
Visual mode is used to make selections of text, similar to how clicking and dragging with a
mouse behaves. Selecting text allows commands to apply only to the selection, such as copying,
deleting, replacing, and so on.
To make a text selection:
vto enter visual mode, this will also mark a starting selection point
- Move the cursor to the desired end selection point; vim will provide a visual
highlight of the text selection
Visual mode also has the following variants:
Vto enter visual line mode, this will make text selections by line
<C-V>to enter visual block mode, this will make text selections by blocks; moving the
cursor will make rectangle selections of the text
To leave visual mode and return to normal mode, press
The visual mode actually has multiple subtypes: visual, block-visual and linewise-visual
- visual: like described above. Enter by pressing
- block-visual: select any rectangular region. Enter by pressing
- linewise-visual: always select full lines. Enter by pressing
Command mode has a wide variety of commands and can do things that normal mode
can’t do as easily. To enter command mode type ‘:’ from normal mode and then
type your command which should appear at the bottom of the window.
For example, to do a global find and replace type
:%s/foo/bar/g to replace
all ‘foo’ with ‘bar’
:Enters command mode
%Means across all lines
/foois regex to find things to replace
/bar/is regex to replace things with
/gmeans global, otherwise it would only execute once per line
Vim has a number of other methods that you can read about in the help
Replace mode allows you replace existing text by directly typing over it.
Before entering this mode, get into normal mode and put your cursor
on top of the first character that you want to replace. Then press ‘R’ (capital R) to
enter replace mode. Now whatever you type will replace the existing text. The
cursor automatically moves to the next character just like in insert mode. The
only difference is that every character you type will replace the existing one.